Repairing Christmas Lights: Replace a C7 or C9 socket

by | Nov 26, 2018

One broken or missing socket on a C7 or C9 Christmas light cord can make for an exasperating installation.

Fortunately, there are replacement sockets available to make minor repairs to C7 and C9 cords. We don’t suggest you install 100’s of these by hand for custom sets but rather consider purchasing a spool with a non-traditional bulb spacing and skipping a socket as required.

Materials required

  • Repair sockets to match your cord style and color – these are specifically designed solely for 18 AWG wire. Be sure to match SPT-1 or 2.
  • ruler
  • washers – the size doesn’t have to be exact but look at the photos to estimate your sizes and configurations
  • channel locks

Assemble your materials. After we took this photo, Dave and I had a discussion about well-used tools and what they look like.

Make sure your light cord is unplugged.

Repairing Christmas Lights: Replace a C7 or C9 socket

If the socket is missing, measure to find where to install the socket.

Repairing Christmas Lights: Replace a C7 or C9 socket

Line up the base of the repair socket with the measured distance.

Repairing Christmas Lights: Replace a C7 or C9 socket

Using a washer protects the socket and evenly distributes the force required to puncture the thick insulation on this style of cord.

Repairing Christmas Lights: Replace a C7 or C9 socket

After you’ve lined up the socket with the base/cap and added the washer, press hard on the socket with the fleshy part of your palm to somewhat pre-seat the socket on the wire. This will not be enough pressure to complete the installation.

Repairing Christmas Lights: Replace a C7 or C9 socket

Grab the smaller washer and hold it on the bottom of the socket.

Repairing Christmas Lights: Replace a C7 or C9 socket

Complete the install by using channel locks to firmly press the contacts of the replacement socket through the insulation into the stranded 18 AWG copper.

Repairing Christmas Lights: Replace a C7 or C9 socket

Test the installation. Plug the set in, then install a bulb.

Job well done!

Repairing Christmas Lights: Replace a C7 or C9 socket


Pin this image for later!

Repairing Christmas Lights: Replace a C7 or C9 socket
Repairing Christmas Lights: Replace a C7 or C9 socket 10

Recent Posts

Get this Look: Traditional Glass C9 Bulbs

Get this Look: Traditional Glass C9 Bulbs

This project used 625 LED bulbs installed into SPT-2 cord purchased in a bulk spool. To create this look, start with this supply list. Materials C9 Spool 1000-feet 9 inch spacing green wire SPT-2 C9 White Glass Light Bulbs C9 Rubber O-Ring Green Male Gilbert Plugs...

read more

7 Comments

  1. a

    The last step WILL NOT LIGHT — because you don’t do electrical work with the system energized!

    Reply
    • Shellie Gardner

      No need to yell. Of course work of this type must not be done with the cord plugged in.

      I’ve updated the blog with a line at the beginning of the process to emphasize that and added a phrase to the text above the last photo to emphasize the point that the cord was unplugged during the work and then plugged in after the repair was complete.

      Good catch.

      Reply
  2. Michael

    What can I do if I need to REMOVE a base and not replace it. Those things are snug and I cannot figure out how to remove it from the line!! HELP!! My project is in danger…. as well as my sanity!!

    Reply
    • Shellie

      Commercially installed sockets aren’t really tailored for removal (as you’ve seen). Without looking at your line, it’s hard to determine what the resulting damage might do to your cord which would put a crimp in your installation.

      Can you simply leave the socket empty and wrap it with a couple turns of electrical tape to keep the spiders out?

      Reply
    • Corey J Dalton

      Unscrew the bulb. Inside the socket should be the two locking tabs that are part of the cap. You need to pry them off the socket where they connect. This will loosen the cap to be popped out.

      Reply
  3. Evelyn P. Richardson

    How do I get my NEW working mini Xmas lights to blink/ flash?? They are NEW out of the box!

    Reply
    • Shellie

      The only way to get them to blink or flash would be to install a red-tipped flasher bulb if a properly rated one was included with your set.

      Keep in mind that this would only be for smaller light strings with little glass bulbs. Not all mini light strings come with flasher bulbs. Note this makes the entire string flash on and off at the same time.

      Reply

Submit a Comment

Your email address will not be published. Required fields are marked *

Related Blog Posts

Get This Look: DIY Lighted Wine Bottles

Get This Look: DIY Lighted Wine Bottles

We developed our craft lights to work specifically for applications like this. Filling bottles with lights is fun. These projects are also fun to purchase at craft fairs - let someone else drill the hole at the base of the bottle. The customer who made the lovely...

read more
Are C7 and C9 bulbs the same?

Are C7 and C9 bulbs the same?

Are C7 and C9 bulbs the same?Short Answer: No, they are very similar but are different sizes. Continue reading the long answer for photos and more information. Longer Answer: C7 bulbs are shorter with smaller diameters than C9s. Both are installed in 18 AWG...

read more
Christmas Lights Lingo!

Christmas Lights Lingo!

Common Christmas Lights Terminology and Vocabulary 5mm This is a shape of LED lens that is about the shape of and slightly smaller than a pencil eraser. It has been referred to as "wide angle" and "conical" in the past since there is a cone shape molded into the lens...

read more
Mini Light Spacing Discussed

Mini Light Spacing Discussed

There are 3 standard spacings for mini lights. Choosing the best spacing is essential for a polished project and can be tricky. We hope a quick visual will help you decide. Here are those three spacings: Standard Christmas Light Spacing A word about lengths of...

read more
Get This Look: Our Christmas Angel

Get This Look: Our Christmas Angel

Ed from Crawford, TX sent us this photo of his beautiful angel project. Here is what he had to say: Earlier this year I contacted you for help in securing lights and clips for our Christmas Angel. We had the angel for years but weather and time took their toll on not...

read more
LED Bulbs: Comparing the Whites! 2022 Edition

LED Bulbs: Comparing the Whites! 2022 Edition

This year, we are releasing Natural Pure White, the third available color white in our LED product line. Commercial C9 LED bulbs with E17 bases and 5mm light strings have been released for the 2022 season. More versions will follow next year. Here is a photo comparing...

read more